Search Results

Brake squeal signatures (2 kHz to 18 kHz) have tonal content highly dependent on the specific brake system structural architecture. The challenge in minimizing squeal involves correctly identifying the conditions (temperature, apply pressure, rotor speed as some basic parameters) of occurrence, defining the underlying structural dynamics of the system and applying appropriate suppression solutions. The quantitative metric of improvement is the cumulative event percentage of occurrence. Design variables of the brake system and performance attribute targets extend the challenge beyond the level of just reducing noise. Consideration of material costs, manufacturing/assembly factors, durability, thermal management as well as other factors narrow the solution space significantly. Compressed late stage development is not uncommon in reaching acceptable levels of performance and is a primary reason for following a well defined process flow with provision for alternative solutions.

The low auto-ignition temperature, rapid evaporation and high cetane number of dimethyl ether (DME) enables the use of low-pressure direct injection in compression ignition engines, thus potentially bringing the cost of the injection system down. This in turn holds the promise of bringing CI efficiency to even the smallest engines. A 50cc crankcase scavenged two-stroke CI engine was built based on moped parts. The major alterations were a new cylinder head and a 100 bar DI system using a GDI-type injector. Power is limited by carbon monoxide emission but smoke-free operation and NOx < 200ppm is achieved at all points of operation.

AS speeds and operational altitudes of modern aircraft continue to increase, it is becoming more and more important that the total drag of the airplane be reduced while the rate of heat dissipation per unit frontal area of radiator be kept as high as possible. The standard method of increasing the temperature difference between cooling medium and coolant has been to use ethylene glycol as a coolant, because its boiling point is much higher than that of water; however, in its pure state glycol has various disadvantages that are not present when a pressure water system is used. This is a sealed system for making use of the physical characteristics of the increase in boiling temperature with pressure. When the radiator receives more heat from the engine than it is dissipating, a small quantity of steam is generated inside the cylinder jackets. The resulting increase in pressure will cause the temperature to rise until a balance is restored between heat rejection and radiator dissipation.

By means of computer simulation, the potential of a Band Variable-Inertia Flywheel (BVIF) as an energy storage device for a diesel engine city bus is evaluated. Replacing both a fixed-inertia flywheel (FIF) and a continuously variable transmission (CVT), the BVIF is capable of accelerating a vehicle from rest to a nearly-constant speed, while recovering part of the kinetic energy normally dissipated through braking of the vehicle. The results are compared with that of conventionally-powered bus. A fuel saving of up to 30 percent is shown with the BVIF-integrated system. The regenerative braking system reduces brake wear by a factor of five in comparison with the conventional vehicle.

Wear of brake disc is normally faced with sophisticated experimental methods, a basic overview on the phenomena related to disc wear is presented in this paper. DTV consists in a heterogeneous wear of the disc surface and it is caused by two factors: run-out and the mechanism of disc wear. The importance of DTV is due to the vehicle vibrations that high DTV values can cause during braking. A model, that considers iron oxide layer evolution on disc surface, can evidence some of the principal characteristics of disc wear. In this model the wear rates of disc gray cast iron and iron oxide layer are considered as some of the principal factors in DTV evolution, as well as the kinetics of the chemical reactions involved.

The production unit number of small diesel engine cars tends to decline except recreational vehicles in Japanese market in recent years, while the production unit number in Europe market keeps on increasing owing to the merits of the durability and the fuel consumption. The small diesel engines will have to be improved in the near future by solving major problems such as noise and vibration pollution, environmental pollution, improvement in performance of diesel engines, in order to expand the production of the engines. This paper refers to a basic study on the experimental and analytical methods for the reduction of resonant vibration in each vibration mode on some cylinder blocks of small high-speed diesel engines in rated engine speed range. Hammering test method, which is easy and useful for measuring frequency response functions, is carried out in the experiments.

Evaluations of the liner pitting protection performance provided by engine coolant corrosion inhibitors and supplemental coolant additives have presented many problems. Current practice involves the use of full scale engine tests to show that engine coolant inhibitors provide sufficient liner pitting protection. These are too time-consuming and expensive to use as the basis for industry-wide specifications. Ultrasonic vibratory test rigs have been used for screening purposes in individual labs, but these have suffered from poor reproducibility and insufficient additive differentiation. A new test procedure has been developed that reduces these problems. The new procedure compares candidate formulations against a good and bad reference fluid to reduce the concern for problems with calibration and equipment variability. Cast iron test coupons with well-defined microstructure and processing requirements significantly reduce test variability.

As a basic tool for fundamental studies on combustion and heat transfer in diesel engines, a new rapid compression machine with a cylinder bore of 200 mm was developed which can realize in it a free diesel flame in a quiescent atmosphere, a diesel flame in a swirl, and a diesel flame impinging on the wall. The piston of this machine is driven by high pressure nitrogen, and its speed is controlled by a sophisticated hydraulic system. This paper describes the details of the mechanism and performances of the machine, and presents some examples of studies conducted with this machine.

A braking force distribution strategy in integrated braking system composed of the main braking system and the auxiliary braking system based on braking pad wear control and hitch force control under non-emergency braking condition is proposed based on the Electronically Controlled Braking System (EBS) to reduce the difference in braking pad wear between different axles and to decrease hitch force between tractors and trailers. The proposed strategy distributes the braking force based on the desired braking intensity, the degree of the braking pad wear and the limits of certain braking regulations to solve the coupling problems between braking safety, economical efficiency of braking and the comfort of drivers. Computer co-simulations of the proposed strategy are performed.

This paper presents a computational study of the airflow features within a motored 4-valve direct injection engine cylinder. An unconventional intake valve strategy was investigated; whereby each valve on the pair of intake valves was assumed to be actuated with different lifts and duration. One of the intake valves was assumed to follow a high-lift long duration valve-lift profile while the other was assumed to follow a low-lift short duration valve-lift profile. The pair of exhaust valves was assumed to be actuated with two identical low-lift short duration valve-lift profiles in order to generate the so-called negative valve overlapping (NVO). The in-cylinder flow fields developed with such intake valve strategy were compared to those produced in the same engine cylinder but with the application of identical low-lift short duration intake valve events.

Improving brake cooling has commanded substantial research in the automotive sector, as safety remains paramount in vehicles of which brakes are a crucial component. To prevent problems like brake fade and brake judder, heat dissipation should be maximized from the brakes to limit increasing temperatures. This research is a CFD investigation into the impact of existing wheel center designs on brake cooling through increased cross flow through the wheel. The new study brings together the complete wheel and disc geometries in a single CFD study and directly measures the effect on brake cooling, by implementing more accurately modeled boundary conditions like moving ground to replicate real conditions correctly. It also quantifies the improvement in the cooling rate of the brake disc with a change in wheel design, unlike previous studies. The axial flow discharge was found to be increased to 0.47 m3/min for the suggested design in comparison to 0.04 m3/min for traditional design.

Knock in Spark Ignited (SI) engines has received significant research attention historically since this phenomenon effectively restricts the compression ratio and hence the thermal efficiency of the engine. The latent heat of vaporization (LHV) of a fuel affects its knock resistance in production engines as well as affecting its Research Octane Number (RON) rating. The reason for this is that evaporative cooling of the fuel lowers in-cylinder gas temperatures resulting in reduced tendency for end-gas auto-ignition. Controlling of the fuel-air mixture temperature to 422 K at the inlet port as per the Motor Octane Number (MON) test method ensures full evaporation of the liquid fuel, and hence LHV is assumed to have little effect during this procedure. LHV therefore has a strong influence on a fuel's Octane Sensitivity (OS) - the difference between its RON and MON values.

Using a previously validated and documented CFD methodology, this research simulated the flow field in the intake region (inlet duct, plenum, ports, valves, and cylinder) involving the four cylinders (#1, #3, #4, #6) of a straight-six IC engine. Each cylinder was studied with its intake valves set at high, medium and low valve lifts. All twelve viscous 3-D turbulent flow simulation models had high density, high quality computational grids and complete domains. Extremely fine grid density were applied for every simulation up to 1,000,000 finite volume cells. Results for all the cases presented here were declared “fully converged” and “grid independent”. The relative magnitude of total pressure losses in the entire intake region and loss mechanisms were documented here. It was found that the total pressure losses were caused by a number of flow mechanisms.

The CFD code KIVA is used in conjunction with a one-dimensional wave action program to simulate exhaust blowdown, in a study of the scavenging and combustion at different loads and constant engine speed, in a single cylinder 4 valved 2-stroke engine configuration, using in-cylinder fuel injection. Two combustion chamber geometries -- a stepped head and a pentroof, were used in this study. The stepped head geometry has a combustion chamber recessed in the cylinder head, and contains the intake valves. The vertical intake port configuration provides a well developed reversed loop flow in the engine cylinder. The pentroof combustion chamber is similar to those used in current 4 stroke engines(1)*. The computational study focuses on the effects of injector orientation, and the subsequent interaction between the fuel spray and ‘loop swirl’ of air in the engine cylinder, and on the resulting combustion characteristics and exhaust emissions.

An experimental study was conducted to investigate piston-impact generated noise in diesel engines. A coherence model was used to represent the noise generating mechanisms of the engine. The model was applied to an in-line turbo-charged diesel engine. Frequency response functions were measured between the cylinder liner vibration and the engine noise, and between the combustion pressure and the engine noise. The noise coherent with piston impacts was separated from the noise coherent with combustion. Guidelines are presented showing how the results of the coherence model may be used for engine design and noise prediction.

ANY aggregation of parts assembled to obtain a mechanical result is a series of compromises. The relative importance of the objectives governs the nature of the compromise. The major objectives to be considered in the design of airplane engines are (1) Reliability (2) Small weight per horsepower (3) Economy of fuel and oil consumption (4) Carburetion that permits of easy starting; maximum power through a range of 30 per cent of the speed range; and idling at one-quarter maximum speed without danger of stalling (5) Ability to deliver full power through a small speed range without excessive vibration (6) Complete local cylinder-cooling under conditions of high mean effective pressure (7) Compactness The automobile engine must have (1) Reliability (2) Silence (3) Carburetion that accomplishes proper and even firing in all cylinders under varying throttle conditions, through speeds covering more than 90 per cent of the speed range of the engine.

A steady-state flowbench measures the mass and angular momentum flux (swirl and tumble) for a given cylinder head intake port design over varying valve lifts and pressure drops. From these two measurements, enhancements in volumetric efficiency and burnrate can be determined. This methodology, however, requires the production and experimental testing of multiple cylinder head castings or soft-prototypes. To help reduce the number of hardware design iterations, an analytical methodology has been developed which uses a new computational fluid dynamics (CFD) simulation tools called PowerFLOW. From a solid model of the cylinder head, PowerFLOW uses automeshing which produces a 10 million Cartesian volume mesh in 4 CPU hrs. The lattice Boltzmann technique used by PowerFLOW is inherently parallel resulting in steady-state results on this mesh in 36 CPU hrs. This paper present a comparison of numerically obtained mass flow rates from PowerFLOW to experimental flowbench data.

Results of a case study in which an unusual liner wear pattern is seen to form within the cylinders of a large marine diesel engine are presented. Analysis of the wear patterns and the wear surfaces are also presented which reveal that the maximum wear corresponds to regions on the liner where “varnish” or “lacquer” films appear to build up from decomposition products of the fuel and lubricants employed. Possible reasons for such wear and film formation are discussed, and compared with frictional and thermal analyses of the ring-liner contacts under operating conditions, with and without the presence of lacquer films. Preliminary results suggest that such films can act as insulation layers to frictionally generated heat between rings and liner, and if allowed to become thick enough can lead to scuffing.

There has to be a good co-relation/ relationship between the pedal effort applied, pedal travel, deceleration level achieved and stopping distance for “good brake feel”. Brake feel also depend upon the time lag between the force applied on brake pedal and the response of braking system. Hence “brake feel” can be improved by reducing the response time of the brake system. Many vehicles are having “poor brake feel” complaints, pertaining to the above mentioned reasons. This paper relates to an improved brake system for automobile in which reduction in reaction time was done by artificially increasing differential pressure head across vacuum booster diaphragm. Brake booster is given an input of compressed air to the valve body during actuation, thereby increasing the differential pressure across the diaphragm. The compressed air is bled from turbocharger-intercooler of the vehicle which is stored in a reservoir, with one way valve, while cruising.